All guides

Annular Snap Fit Design: Bead Sizes for 3D Printed Caps

7 min readBy Mandarin 3D

An annular snap fit works when the ring can stretch over the bead without cracking: the strain is 2 x bead height / diameter, and it should stay under about 2% for PLA and 2.5% for PETG on a joint closed once or rarely, or half that for a cap taken off every day. On a solid 20 mm PLA cap that allows a bead of only 0.1-0.2 mm per side.

That is smaller than a 3D printer's tolerance, which is the real lesson of this page: printed annular snaps work best slotted into fingers, on bigger diameters, or with both parts flexing. Our snap-fit guide covers the joint types and the cantilever page covers hooks; this page is the math for round ones.

How an annular snap fit works

A bead runs around the post (or the inside of the cap) and a groove waits on the other part. Pushing the cap on, the bead stretches the cap open, or squeezes the post in, until it drops into the groove and both parts relax. Pen caps, bottle caps, lens caps and the lids of round boxes all work this way.

Unlike a cantilever, the whole ring stretches at once. Its circumference grows in proportion to its diameter, so the hoop strain is the change in diameter divided by the diameter. A bead 0.1 mm tall per side opens a 20 mm cap by 0.2 mm: 0.2 / 20 = 1%.

That assumes the other part doesn't give. The Covestro snap-fit design guide (formerly Bayer) notes that when both parts are equally flexible, each takes half the strain, so the bead can be twice as tall.

Bead height tables

The design strains come from the same Bambu Lab datasheets as our cantilever page: bending strength over bending modulus gives 2.8% for PLA and 3.8% for PETG at full strength; we design at 2% and 2.5% for a joint closed once or rarely, and half that for one opened every day.

Largest bead height per side, in mm, with the other part rigid. Double it if both parts flex equally.

Diameter at the jointPLA, rarely (2%)PLA, daily (1%)PETG, rarely (2.5%)PETG, daily (1.25%)
10 mm0.100.050.130.06
15 mm0.150.080.190.09
20 mm0.200.100.250.13
30 mm0.300.150.380.19
40 mm0.400.200.500.25
60 mm0.600.300.750.38

Our dimensional tolerance is about ±0.3 mm or ±0.5%, whichever is greater, and most hobby printers are similar. Under about 40 mm, every number in the daily columns is smaller than that. A solid printed ring at these sizes either doesn't click or cracks, depending on which way the print came out.

Why solid rings take so much force

A cantilever bends a short arm. An annular bead has to stretch a whole band of the cap around it, so the force is much higher. Covestro's formula for a joint near the open end of the cap is P = y x d x E x X, where y is the change in diameter, d the diameter, E the stiffness and X a geometric factor from the wall thickness. The push to close it is P times (friction + tan of the lead-in angle) / (1 - friction x tan of the lead-in angle).

For a 20 mm cap, a bead 0.1 mm tall per side (1% strain), PLA at 2,750 MPa and PETG at 1,950 MPa, friction 0.3:

Cap wallXPLA, 30 degree lead-inPLA, 45 degree lead-inPETG, 30 degree lead-in
1.2 mm0.016187 N327 N133 N
1.6 mm0.024276 N483 N196 N
2.0 mm0.032370 N648 N262 N

276 N is the weight of about 28 kg. The formula assumes a perfect ring on a post that doesn't give at all, so treat these as an upper bound for comparing designs, not a promise. The direction is right, though: a thinner wall, a gentler lead-in and PETG all help, and a joint deeper inside the cap gets up to 3 times harder. The guide counts a joint as near the end if it sits within 1.8 x the square root of diameter x wall from the open end: 10 mm for a 20 mm cap with a 1.6 mm wall.

Slot it: the fix for printed caps

Cut the skirt of the cap into fingers and each finger bends like a cantilever instead of stretching the ring. Two slots across a 20 mm cap, 1.2 mm wide and 8 mm deep, make four fingers 8 mm long. Using the cantilever formula, a 1.6 mm finger can bend 0.27 mm at PLA's everyday 1%, nearly three times the solid ring's 0.1 mm, and enough to survive a print that comes out 0.1 mm off.

The force falls too. By the flat-beam formula each finger takes about 24 N, about 100 N for the four with a 30 degree lead-in. Curved fingers are stiffer than flat ones, so expect somewhat more, but a hand can do it.

Other ways to get there:

  1. Make the post hollow with a thin wall so it squeezes in and takes half the strain.
  2. Use PETG for caps taken off often: 25% more bead at the same strain and lower force.
  3. Go bigger. A 60 mm lid allows six times the bead of a 10 mm cap.

Print them standing up

Print the post upright and the cap with its open end up. Each layer then holds a full ring, so the cap stretches along its layer lines, the strong direction. Give the bead and the groove 45 degree faces top and bottom and both print without supports. A 45 degree return comes apart with a firm pull; a flat return holds until something breaks.

What a test pair costs

We drew the 20 mm joint from this page as a test pair: a post on a 30 mm base, 12 mm tall with a 2 mm wall and a bead 3.5 mm above the base, and a cap with a 1.6 mm wall, 0.15 mm gap per side and a matching groove, printed side by side. The solid version has a 0.25 mm bead, so 0.1 mm of interference per side (1%). The slotted one has a 0.4 mm bead, 0.25 mm per side, on four 8 mm fingers (0.94% in each finger). Live quotes from our quote API on November 19, 2026, one set, shipped by USPS Ground Advantage anywhere in the US, before tax:

Test pairPlasticPrint timePLA deliveredPETG delivered
Solid ring6.1 g16 min$9.45$10.31
Four fingers6.0 g16 min$9.44$10.31

Most of the price is the $3.50 order fee and postage, so put the test joint on the same order as the real part if you can. PETG is made to order in black or white and adds 3 to 5 business days.

Get it printed

Drop your STL, 3MF or STEP file in the box below for an instant price in PLA or PETG, and add the file check for $5: we look at the snap before printing and email you if the bead looks too tall for the ring. No file? Describe the cap to the AI designer with the diameter and the bead from the tables. Need a cap for a tube or a chair leg rather than a snap? The round tube end caps push on with crush ribs, made to the diameter you measure, and the quote shows the ship date before you pay.

Questions

How do you calculate an annular snap fit?

The ring stretches by the interference on its diameter, so the strain is 2 x bead height / diameter. Keep it under the material's design strain: about 2% for PLA and 2.5% for PETG for a joint closed once or rarely, half that for one opened every day.

How big should the bead be on a 3D printed snap-on cap?

On a solid 20 mm cap in PLA, about 0.1 mm per side for a cap taken off every day and 0.2 mm for one closed once. That is smaller than a printer's tolerance, so most printed caps are slotted into fingers: four 8 mm fingers allow about 0.25 mm even for daily use.

Why is my annular snap fit so hard to push together?

A solid ring has to stretch all the way around at once. By the Covestro formula a 20 mm PLA cap with a 1.6 mm wall and a 0.1 mm bead takes about 280 N to push on, the weight of 28 kg. Slots, a thinner wall or a hollow post bring it down.

Which way should an annular snap fit be printed?

Both parts standing up, open end of the cap facing up. Then the ring stretches along the layer lines, the strong direction, and the bead and groove print with 45 degree faces and no supports.